Split Taper Bushing

The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for make use of with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need. For employ with 5/8” shaft sizes. Comes with set screws. Further Features: Made of Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, ideally lowering readily available requirements and allowing for adjustments in shaft size if necessary. The barrel of the split tapered bushing is definitely split in two places and is usually keyed to the shaft. The barrel OD can be keyed to the drive component as well. The advantage of the split tapered bushing could it be will hold, whether or not the fasteners become loose. Split tapered bushings will be interchangeable between manufacturers.

Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are created from high quality engineered resources with wonderful tolerance. The feature is easy to make use of and needs no extra alteration. These bushings can go well with almost a myriad of assemblies and sizes. They will be the best choice in style for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total range of both metric and imperial obtainable.
Standard range meets up to 125mm/5″ shafts & Hub diameter required will depend on the application.
Complete short reach range readily available, for compact light-weight assemblies & Clean, Compact Design.
Simple installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Comes with 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that's built for durability and strength. U1 bushings are being used in an extensively wide selection of applications, which include; sprockets, shaves, pulleys, gears, and much more, we likewise offer most of these goods. What pieces this bushing apart is the high-quality steel engineering along with exact manufacturing and top quality control; this means that you always get a premium quality regular product. What really pieces us apart from the other folks is our experienced expert staff members and our company-wide goal of customer satisfaction.
1. Be certain the tapered cone surfaces of the bushing and the within of the driven item are clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or additional part type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to assure sliding match on shaft.
4. With major on shaft, slide the sprocket or other part type to the required position on the shaft. Make sure you leave the heads of the cap screws attainable.
5. Align the sprocket or component type, tighten the screws alternatively and progressively until they are pulled up tight. Do not make use of extensions on the wrench handles and don't permit the sprocket or part to become drawn i contact with flange of bushing. At this time there must be a gap between your bushing flange and sprocket, make sure this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with positive clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key of all sizes for great drive and greater torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to maintain concentric bores
Available in inch, metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Twice Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys on both the shaft and merchandise to supply the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest amount of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, permitting them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for employ with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and may be purchased on the same page as the pulley you will need. For make use of with 5/8” shaft sizes. Comes with set screws. Additional Features: Made of Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, ideally lowering readily available requirements and allowing for adjustments in shaft size if necessary. The barrel of the split tapered bushing is split in two spots and is usually keyed to the shaft. The barrel OD is also keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.